Hobart Welders
Home » Products » Plasma » AirForce® 27i
AirForce 27i
Printable Version
Bookmark and Share

AirForce® 27i Plasma Cutter


Buy NowWhere To Buy

With MVP™ (Multi-Voltage Plug) for 120V or 240V Input Power

Need to cut steel? Thinking about an oxy acetylene cutting torch to do the job? Consider a plasma cutter. This simple technology uses an electrical arc and compressed air to cut steel, aluminum, and other conductive metals.

The AirForce™ 27i is an economical plasma cutting system for all conductive metals. Inverter-based design and reliable technology pack a lot of performance into a very portable package. This power source adapts to your work site by operating from either 120V or 240V power through standard household outlet using the Multi-Voltage Plug (MVP).

Compared to the complexities of an oxy fuel cutting torch system, plasma cutting is easy:

Comes complete with:
  • XT30R torch with 12 ft (3.66 m) lead and consumables
  • Heavy-duty work clamp with cable
  • 10 ft (3 m) power cord with 120/240 VAC, 20 A MVP plug
Input Power:
  • 120 VAC, 20 amp circuit, single phase
  • 120 VAC, 15 amp circuit, single phase
  • 240 VAC, 50 amp circuit, single phase
PlasmaAir Plasma Cutting
Skill Level: Low
  • Sheet Metal
  • HVAC
  • Auto Body
  • Farm/Ranch
  • Plumbing
  • Inverter Design - Powerful cutting ability at half the weight of prior model (AirForce 400). Weighs only 27.8 lbs.
  • Capable with Engine-Driven Welders - Complete cutting capability when powered by an engine-driven welder with a 240 V generator power outletof 6 kW or more.
  • New High-Performance Ergonomic Torch - The new XT30R torch is designed for increased comfort, more efficient cooling and longer lasting cutting tips.
  • Multi-Voltage Plug (MVP) - Allows you to connect to common 120 or 240 V power receptacles without the use of any tools - simply choose the plug that fits the receptacle
  • Post-flow Air Cooling - Cools the torch and tip after cutting, extending life of replaceable tip and electrode.
  • Fan-On-Demand - Runs only when needed reducing dust/debris pulled into unit.
  • Wind Tunnel Technology - Prevents abrasive dust and particles from damaging internal components.
  • Thermal Overload Protection - Built to withstand tough working environments. Rated for 35% duty cycle at 104° Fahrenheit. Duty cycle will increase as environmental temperature decreases.
  • Line Voltage Compensation (LVC) - Provides peak performance power under variable input voltage conditions (±15%) for steady and cleaner ending cuts.
  • Power Factor Correction - Expands operator’s work area via extension cords while minimizing nuisance trips caused by voltage drops.
#770771 Protective Cover Protective Cover
Weatherproof nylon resists stains and mildew, and protects the finish of your plasma cutter.
#770796 (2) Tip Kit
#770793 Cup, Swirl Ring, O-Ring, Deflector Kit
#770791 (2) Electrode Kit
#770799 (1) Drag Shield Kit
HP-70 Kit
Stock Number #500565 AirForce 27i
Rated Output at 35% Duty Cycle 240 V - 27 A, 92 VDC
120 V - 20 A, 88 VDC
Max. Open-Circuit Voltage 400 V
Amps Input at
Rated Output, 60 Hz
120V (15 A) 20.6
120V (20 A) 28.8
240V 13.9
Plasma Gas Flow/Pressure 3.0 CFM (85 L/min) at 90-120 PSI (621–827 kPA) recommended
Dimensions H: 11-1/4 in. (286 mm)
W: 8-1/4 in. (210 mm)
D: 14-1/4 in. (362 mm)
Net Weight 27i w/torch: 27.8 lb (12.6 kg)
Ship weight: 32.6 lb (14.8 kg)
  • Cuts faster than oxy fuel
  • More precise cut, thinner kerf, less slag to clean up
  • Smaller heat-affected zone for less warping
  • No gas pressure settings or flame tuning needed
  • No preheating of metal prior to cutting
Steel Stainless
Aluminum Cast Iron Copper Brass Titanium Magnesium
Air Plasma X X X X X X X X